Description
- Amplifier Signal Type – Audio
- Amplifier Type – Power Amplifier
- Warranty – Yes
- Spec Sheet available – Yes
- Spec Sheet available – Yes
- Operating Temperature (Maximum): 185 F
- Operating Temperature (Minimum): 167 F
- AC Voltage: 300 Volts
- Warranty (Length/Type): 4 year
- Product Weight: 26.46 lbs
- Maximum Frequency Response (Bandwidth): 20 kHz
- Maximum Frequency Response (Bandwidth): 20000 Hz
- Minimum Frequency Response (Bandwidth): 20 Hz
- Minimum Frequency Response (Bandwidth): 0.02 kHz
- Impedance: 100 ohm
- AC Voltage (Maximum): 240 Volts
- AC Voltage (Minimum): 100 Volts
- Depth: 18.70 in
- Height: 1.75 in
- Width: 19 in
- Certification: CE, CSA and KETI approved
- 2-Channel mode(2ohm): 2×6000 W
- 2-Channel mode(4ohm): 2×4000 W
- 2-Channel mode(8ohm): 2×2000 W
- Mono-Bridge mode(4ohm): 1×12000 W
- Mono-Bridge mode(8ohm): 1×8000 W
- Crosstalk separation: > 66 dB @ 1 kHz
- THD+N/SMPTE IMD/DIM 100 IMD: <0.5% from 1 W to full power (typically <0.05%)
- Slew Rate: 50 V/s @ 8 ohm, input filter bypassed
- Damping factor @ 8 ohm: >5000 @ 20-200 Hz
- A/D Converter: Dual 24bit 96 kHz Tandem® architecture with 127 dBA of dynamic range and THD <0.005% (20 Hz – 20 kHz)
- D/A Converter: Dual 24bit 96 kHz Tandem® architecture with 122 dBA of dynamic range and THD <0.003% (20 Hz – 20 kHz)
- Memory: 8 MB (RAM) plus 2 MB (flash for presets)
- Presets: 50 stored locally + 150 stored on a smartcard
- Digital audio input: AES3 (glitchless fallback to analog audio selectable)
- Delay for time alignment: up to 4 s on the input section, up to 32 ms per output, sample-by-sample stepping
- Crossover Filters: Butterworth, Linkwitz-Riley, Bessel, Arbitrary Asymmetric, 6dB/oct to 48dB/oct (IIR), linear phase (FIR), hybrid (FIR+IIR)
- Output Equalizer: 16 fully parametric filters per channel, IIR: peaking, hi/lo shelving, hi/lo pass eq, band pass, band stop, all pass. Custom FIR up to 384 taps @ 48 or 96 kHz
- Input Equalizer: Three layers (PEQ, raised cosine, shelving), 32 filters each + group filters, up to 256 filters per channel
- Cable compensation network: up to 2 ohm negative/positive wire compensation (Active DampingControlTM)
- Limiters: Power limiter (TruePower™, RMS voltage, RMS current) + Peak Limiter
- Indicators: 7 meter LEDs: 5 x green, 1 x yellow, 1 x red, top yellow and red show alarm with protect description on LCD panel
- Controls: 4 pushbuttons, function depending on user menu
- Power Switch: Mains switch
- Network data port AESOP incl. AES3: 2 x RJ45 with activity LEDs
- Maintenance: SmartCard reader/writer for firmware updates and preset storage. Easily accessible dust filter foam behind two steel covers
- Audio signal input connectors: Analog: 2 x balanced Neutrik® Combo XLR female/1/4” jack; AES3: use channel 2 XLR
- Loudspeaker output connectors: 2 x Neutrik® Speakon NL4MD
- Network data port Ethernet: 2 x RJ45 with activity LEDs
- Aux voltage: 1 x 2-pin Phoenix P. 3.81mm
- AC Mains: AMP CPC 45A on rear panel; AMP CPC 45A connector mounted on a 3 x 5mm2 (10AWG) cable
- Chassis: 1 mm / 0.04” steel chassis and removable dust cover ; 3 mm / 0.12” steel front panel, screw hole protection, side reinforcement & rear support
Reviews
There are no reviews yet.